Advanced Lines plays a crucial role in supporting the Oil and Gas industry by
supplying a wide range of equipment to our esteemed clients.
supplying a wide range of equipment to our esteemed clients.
CENTRIFUGAL PUMP
Centrifugal Pumps area sub-class of dynamic axisymmetric work- absorbing turbomachinery. Centrifugal pumps are used to transport fluids by the conversion of rotational kinetic energy to the hydrodynamic energy of the fluid flow. The rotational energy typically comes from an engine or electric motor. The fluid enters the pump impeller along or near to the rotating axis and is accelerated by the impeller, flowing radially outward into a diffuser or volute chamber (casing), from where it exits
Available Pumps:
- 5x4x14
- 5X6X11
- 6X5X11
- 6X5X11 20BPM
- 6X5X14 20 BPM
- 6X10X12
- 10X12
FILTRATION UNIT
Our Dual Vessel Cartridge Unit (TDW) is the
most commonly used filer cartridge unit in the
Oilfield industry. This, offshore proof, skidmounted filter unit can be supplied as a
cartridge, bag or combination unit, equipped
with all necessary valves and safety features.
Our Dual Vessel Cartridge Unit offers the most
cost-effective way to clean-up all possible
oilfield fluids. It allows you to simultaneously
filter with once vessel and easily change
BATCH MIXER
- Engine: Caterpillar C9 300 bhp Diesel Engine or Equivalent
- Tanks: 2 x 70 BBL Mild Steel Tanks usable volume of 60-65 BBL per tank.
- Coating: Derekane Coating for Anti Acid applications up to 32% HCL for Tanks
- Agitators: One (1) Each Agitator in each Tank
- C Pump: Two (2) C Pumps of Size – 4 x 5 x 11
- Controls: Mounted in a Control Panel with Air Strut supported with closing lid.
- Valves: Acid Resistant PTFE Butterfly Valves
CEMENT BULKER
The trailer-mounted cement transporter is
built according to ASME section VIII Division 1
and is capable of handling bulk material.
The banana-shaped cement transport trailer hauls 1,060 ft3 (30 cubic meters) volume in two equal compartments and is designed to perform at a maximum working pressure of 40 psi.
The interior is designed to allow dry material to flow out under airstream pressure to the surge tank or the field silo. Two manways are located on the top of the tank for performing maintenance operations and for top loading of sand.
The banana-shaped cement transport trailer hauls 1,060 ft3 (30 cubic meters) volume in two equal compartments and is designed to perform at a maximum working pressure of 40 psi.
The interior is designed to allow dry material to flow out under airstream pressure to the surge tank or the field silo. Two manways are located on the top of the tank for performing maintenance operations and for top loading of sand.
FRAC TANK TRAILERS
The Frac Tank Trailer is a 500 BBL singlecompartment unit suitable for use with HCL up to a concentration of 32%. Designed for use in
all land-based operations, the Frac Tank Trailer
(500 BBL Acid) features a manifold which
allows the series connection of multiple units,
providing the flexibility to meet low and high
fluid storage demands.The tank incorporates a Tnemec lining
specifically formulated for high acid resistance
and longevity. Further, should the lining suffer
any physical damage, repairs are relatively
simple. Built as a self-contained trailer unit, the
tank can be transported and placed on site
easily without the requirement for any
specialist lifting equipment.
ABOVE GROUND STORAGE TANK (AGST)
- Capacity: 15,000 bbl. to 80,000 bbl.
- Capable to operate in Extreme Conditions
- Geo-Textile Membrane
- Valmex 7616 Waterproofing Membrane
- Operating Temperature: upto +70°C
- Warranty of 10 Years to Manufacturing Defects
ACID STORAGE TANK
- Capacity: 5000 USG Skid Mounted
- Circulating Line: 1 X 4” Fig 207 Union
- Discharge Line: 1 X 4” Fig 207 Union
- Lining: Derekane 470-300
- Single Compartment, Double Valve (4”) At Discharge Line, Complete Handrails On Top.
ISO CRYOGENIC TANKS
The ISO-PACK 2000 6bar is a vacuum insulated
liquid gas transportable / storage tank,
designed to transport liquid Nitrogen by road,
rail and sea. The tank dimensions meet the
requirements of DNV, IMO and CSC.
The ISO-PACK is used primarily for offshore operations and OHS customers include all major well service companies. In addition to European and International approvals, the ISOPACK 2000 (6bar) also has US DOT approval which permits the use of the tank in North America.
The ISO-PACK is used primarily for offshore operations and OHS customers include all major well service companies. In addition to European and International approvals, the ISOPACK 2000 (6bar) also has US DOT approval which permits the use of the tank in North America.
ACID TRANSPORTER
- Capacity: 8000 USG Trailer Mounted
- Construction: A36 Material With Shell Thickness Of 6mm
- Fill Line: One (1) X 4” Line With 1 Each Acid Resistant Butterfly Valve.
- Drain Line: One (1) X 4“ Drain Line From Each Compartment With 1 Each Acid Resistant Butterfly Valve.
- PRV: Each Compartment Has A Clay And Bailey Manway W/ PRV
- Lining: Derekane 470-300 Lining
- Tyres: 11R 22.5 R187 Sumitomo With Disc Rims
- Brakes: Spring Brakes On 2 Axles
- Landing Leg: JOST A400
- Compartment: Three (3) Compartments
- Manhole: One (1) Each Per Compartment On Top Of The Tank
NITROGEN TRANSPORTER
- Capacity: 7000 USG Trailer Mounted
- Design Code: EN13530-2 (ADR/TPED Certification Excluded)
- Design Pressure: 4 Barg
- Design Temp.: -196 Deg C / +37 Deg C
- Internal Material: 1.4301 / 1.4307 Stainless Steel
- Outer Material: S355J2+N Carbon Steel
- Transfer Pump: Cryostar GBS 155 Centrifugal Transfer Pump
- Tyres: Bridgestone / Good Year
- Brake System: EBS WABCO
- Axles: BPW Or SAF Pneumatical Axles
FRAC PUMP
A frac pump is a high-pressure, high-volume
pump used in hydraulic fracturing treatments.
Hydraulic fracturing is a well stimulation
technique where fracking liquid (a mixture of
mostly water and sand) is injected into rock
formations at high-pressures, allowing for the
extraction of natural oil and gas. Frac pumps
have evolved throughout history to
accommodate the increasing demand of
pressure pumping services companies around
the world as operators are required to push
drilling into more complex geological
formations to ensure supply.
TWIN PUMP
- Skid mounted twin pumping unit
- Skid: L x W x H : 8.4m x 2.6m x 3.0m
- Deck engine: 2 x Detroit Diesel8v-71 305bhp.
- Transmission: Allison CLBT-754
- Control panel data acquisition equipment, recording system.
- Triplex pump: 2 x Gardner Denver PG (3 3/4″ 10,000psi and 4.5″ 5,000psi).
- Centrifugal pump: 2 x Garden Denver 5″x4″.
- Fluid and air tank: hydraulic, diesel and air tanks.
- Displacement tank: One 20BBL divided into 2 compartments
- High and low pressure piping.
LIFE SUPPORT UNIT
Life Support Unit (LSU) is specifically designed
to support the requirements of Cabin Rig Site
Management. LSU has a Fresh Water Tank,
Waste Water Tank, Diesel Tank, and
Generator. All tanks/equipment are fixed on
the skid mounted, the set is built to operate
for long periods under site conditions with
minimal supervision and attention.
NITROGEN PUMP
The product range includes Nitrogen Pump/Converter units with flow rates up to 180K scf/hr and pressures up to 15,000psi. All pumps are certified as a minimum to DNV 2.7-1 and Zone II, with ATEX and NORSOK certification options also available.
This nitrogen pump unit outputs up to 180k scf/hr of nitrogen gas at temperatures of 20 deg C (70 deg F). Units can be provided rated to 10,000psi (690 bar) or 14,500psi (1000 bar) with a PED approved vaporizer pot.
This nitrogen pump unit outputs up to 180k scf/hr of nitrogen gas at temperatures of 20 deg C (70 deg F). Units can be provided rated to 10,000psi (690 bar) or 14,500psi (1000 bar) with a PED approved vaporizer pot.
SINGLE TRIPLEX PUMP
Triplex pumps are positive displacement type
pumps used to move both thin and viscous
fluids with a triple mechanism all driven by a
single power source
- Dimensions: 8000 (L) X 2400 (W) X 300 (H)
- Engine: 8V92 Detroit Diesel Engine, 430 HP Or Equivalent
- Triplex Pump: HT-400 Pump Equipped With 3.5” Plunger And Stroke, MAWP – 10000 Psi, Min Rate – 2.5 Bpm At 6290 Psi
RIG CAMP UNIT
Advanced Lines Est. with its local
Manufacturing Facility for Customized
Portacabin’s offers various sized Offices,
Sleepers etc. fulfilling Aramco requirements
with Quality, Safety and Comfort.
These Portacabin’s are supplied to major Aramco Service Companies in the Kingdom supporting their various operations in the Rig and Well Sites. Our Portacabins are fully customizable for various purposes to fulfil Client’s requirement
These Portacabin’s are supplied to major Aramco Service Companies in the Kingdom supporting their various operations in the Rig and Well Sites. Our Portacabins are fully customizable for various purposes to fulfil Client’s requirement
- 40ft. Cabin with One (1) Office and One (1) Majlis.
- 40ft. Cabin, Two (2) Men Sleeper with Two (2) attached WC.
- 40ft. Cabin, Four (4) Men Sleeper with Two (2) attached WC.
- 40ft. Cabin, Eight (8) Men Sleeper with Two (2) attached WC.
- 40ft. Cabin, Customized Meeting Room Facility.
- 20ft. Cabin, Mosque Facility.
- 40ft. WC Facility.
- Custom Sized Security Cabin.
- Custom Sized Spooling Cabin.
PORTABLE LIGHT
The professional grade L8WKUB-60HZ- T4F light tower provides the superior lighting your worksite requires. The L8 is dependably rugged, featuring durable protective reflector housings with tempered glass. These light towers feature reliable engines and a larger, brighter coverage area. If your event or workday doesn’t start until the sun goes down, the L8.
- Make Kubota D1105
- Emissions Tier Level Tier 4 Final (T4F)
- Number of Cylinders/Displacement – cu In (L)3/69 (1.1)
- Power @ Rated Speed – bhp (kW) @ 1800 rpm13.6 (10.1)
- Cooling System Water DC System
- Voltage/Battery Capacity12 V/600 CCA
- Fuel Type/Useable Fuel Capacity – gal (L) Diesel/27 (102)
- Runtime with 4 lights – hr52
DIESEL GENERATOR
- Generator Type : Open Type
- Power Rating : 200 KVA, 160 KW
- Engine Model No. : P086TI
- Voltage : 380/220 V
- Power Factor : 0.8
- Ambient Temp. : 50 ° C
- Alternator Brand : MARELLI
- Speed Governor Type : Mechanical Type (Standard)
- Power Application : Prime Power
- Engine Brand : DOOSAN
- Number of Cylinder : 6 Cylinder – Line type
- Total output Amps. : 303 Amps
- Frequency : 60HZ, 1800 RPM
- Insulation Class : Class H
- Alternator Model No. : MJB250LA4
- Controller : Unit Mounted DSE 7110.
DIESEL GENERATOR SOUNDPROOF
- Generator Type : Soundproof Type
- Power Application : Prime Power
- Power Rating : 200 KVA, 160 KW
- Engine Brand : DOOSAN
- Engine Model No. : P086TI
- Number of Cylinder : 6 Cylinder – Line type
- Voltage : 380/220 V
- Total output Amps. : 303 Amps.
- Power Factor : 0.8
- Frequency : 60HZ, 1800 RPM
- Ambient Temp. : 50 ° C
- Insulation Class : Class H
- Alternator Brand : MARELLI
- Alternator Model No. : MJB250LA4
- Speed Governor Type : Mechanical Type (Standard)
- Controller : Unit Mounted DSE 7110
AIR COMPRESSOR
- Compressor (Low Pressure & High Pressure)
- Free-Air Delivery – cfm (m³/min)450 (12.7)400 (11.3)
- Rated operating Pressure – psig (bar)150 (10.3) 200 (13.8)
- Pressure range – psig (bar)80 – 175 (5.5 – 12.1)80 225 (5.5 –15.5)
- Air Discharge outlet size – in (mm)1.25 (31.75) 1.25 (31.75)
- Air Discharge outlet Quantity11
- Fuel Tank Capacity – gal (L)63 (227)63 (227)
- DEF Tank Capacity – gal (L)5 (19)5 (19)
- Hours of operation @ Full Load8,58,3
DIESEL TANK
Advanced Lines Group manufactured a diesel tank with a capacity of 1500 Liters. The dimension of the diesel tank is 1250 x 1250 x 1950 mm.
CHEMICAL INJECTION PUMP – DHDA66
Air-operated, high-flow, double-acting hydraulic pumps for pressure testing, chemical injection, and hydraulic power. Features:
- Infinitely variable output pressure and flow
- Holds static pressure without generating heat or consuming power.
- Standard models are suitable for oil or water applications
- Well proven and trouble free operation
- Designed for ease of maintenance
- Low cost servicing ase of maintenance
- Robust construction
SHALE BIN (7/10 meters)
Shale Bins are made of heavy-duty industrial steel, it is used on drilling rig sites to collect drill cuttings. High, low, and four-sided bins are designed to hold all types of solid waste or drill cuttings generated on project sites. Features & Advantages:
- The thickness of the steel plate prevents warping.
- Suited for drill cuttings management, mix-off, and waste holding of environmental solids.
- The four-sided shale bin is ideal for the complete containment of waste by-products and limits on-site contamination.
WELL TEST PUMP UNIt
Specifications:
- Low pressure pump, displacement/cycle: 260ml
- Low pressure pump ratio: 12:1
- Low pressure pump maximum pressure:1000 psi
- High pressure pump ratio: 100:1
- High pressure pump, displacement/cycle: 13.4ml
- High pressure pump maximum pressure:10,000 psi
- Recommended pump air requirement:75 cfm
- Maximum air supply pressure:1 40 psi
- Minimum air supply pressure: 90 psi10k
- System relief valve set:10,400 psi
- 1k system relief valve set:1,300 psi
